24brezen

1 files changed, 77 insertions, 74 deletions

diff --git a/text/chipy.tex b/text/chipy.tex
index e91ce9c..4642918 100644
--- a/text/chipy.tex
+++ b/text/chipy.tex
@@ -175,7 +175,7 @@ nRF9160 Feather, made by CircuitDojo, is a design with pin headers compatible wi
 SparkFun Thing Plus nRF9160, made by SparkFun, is another board with Adafruit Feather footprint and similar to Icarus IoT Board v2 described above, however with USB-C connector and providing 4 MB SPI flash memory, LiPo charger, low power RTC, a button, a LED, two U.FL antennas for LTE and GNSS
 \cite{sparkfundesc}.
 
-\subsubsection{Connexio Stratus}
+\subsubsection{Connexio Stratus (Pro)}
 
 \begin{figure}[H]
   \begin{center}
@@ -188,6 +188,8 @@ SparkFun Thing Plus nRF9160, made by SparkFun, is another board with Adafruit Fe
 Connexio Stratus, a crowd-funded development board, has a similar design to the SparkFun board above, adding SIM with 500 MB of mobile data, energy harvesting integrated circuit for Li-ion and NiMH battery charging, LiPo battery connection and charging, 2 push-buttons, 1 LED, SHT4x temperature and humidity sensor, LIS2DH 3-axial accelerometer
 \cite{connexiodesc}.
 
+% TUTUT
+
 Comparisons of the main parameters of the most common nRF9160 boards is provided in the following table \ref{tab:nrfmodules} taken from \cite{connexiodesc}:
 \begin{table}[H]
   \begin{center}
@@ -229,76 +231,77 @@ Comparisons of the main parameters of the most common nRF9160 boards is provided
 
 %%-------------------------------------------------------------------------------------------
 
-\section{Quectel RM520N}
-
-\begin{figure}[h!]
-  \begin{center}
-	  \includegraphics[width=0.6\textwidth]{obrazky/RM520N.png}
-  \end{center}
-	\caption[Quectel RM520N]{Quectel RM520N series front view\cite{rm520ndatasheet}}
-	\label{}
-\end{figure}
-
-RM520N is a 5G Sub-6GHz IoT module, made by Chinese company Quectel, optimized for IoT and eMBB applications with worldwide spectrum coverage, but capable of also 3G/4G multi-mode operation. The module is made in an M.2 form factor (30 x 52 x 2.3 mm) with 4 antenna connectors and is compatible with \ac{3GPP} Release 16 specification, supporting  both 5G NSA (data rates: 3.4 Gbps DL / 550 Mbps UL) and SA modes (data rates: 2.4 Gbps DL / 900 Mbps UL).
-
-The RM520N is an industrial-grade module for industrial and commercial applications. It should cover nearly all the mainstream carriers worldwide and support Qualcomm® IZat location technology Gen9C Lite (GPS, GLONASS, BDS and Galileo). The integrated GNSS receiver simplifies the product design.
-
-It communicates using USB and PCIe drivers provided by Quectel for Windows 7 or higher, Linux, and Android. Main anticipated usage are industrial routers, home gateways, laptops / tablet PCs as well as IoT applications \cite{rm520ndatasheet}.
-
-The module comes in two variants: RM520N-GL with global coverage and RM520N-EU with EU frequency regulatory spectrum.
-
-\subsection{Modules with RM520N}
-
-Development support for RM520N modules is provided by a Chinese company Waveshare \cite{waveshare1}\cite{waveshare2}
-making several hardware kits for rapid development and implementation with RM520N and having a distribution network across EU (e.g. \url{https://rlx.sk/sk/vyhladavanie?controller=search&s=RM520N})
-
-\subsubsection{Dongle}
-\begin{figure}[H]
-  \begin{center}
-	  \includegraphics[width=0.6\textwidth]{obrazky/rmdongle.jpg}
-  \end{center}
-	\caption[Waveshare dongle]{Waveshare dongle\cite{rmdongle}}
-	\label{}
-\end{figure}
-
-5G DONGLE module \cite{rmdongle}
-providing simple expansion board with 4 SMA antenna connectors, nano SIM card holder, M2 connector for RM520N, heatsink and USB3.1 port for connecting to PC or Raspberry Pi.
-
-\subsubsection{Raspberry Pi HAT}
-
-\begin{figure}[H]
-  \begin{center}
-	  \includegraphics[width=0.6\textwidth]{obrazky/rmpi.jpg}
-  \end{center}
-	\caption[Waveshare dongle]{Waveshare dongle\cite{rmpi}}
-	\label{}
-\end{figure}
-
-5G HAT for Raspberry Pi \cite{rmpi}
-, with a case for Raspberry Pi 3B/4B, onboard USB3.1 and USB-C ports, 2x SIM card slot, 4 antennas, 3A power supply circuit.
-
-\subsubsection{USB/Ethernet converter}
-
-\begin{figure}[H]
-  \begin{center}
-	  \includegraphics[width=0.6\textwidth]{obrazky/rmeth.jpg}
-  \end{center}
-	\caption[USB/Ethernet converter]{USB3.1 / Gigabit Ethernet converter to 5G\cite{rmeth}}
-	\label{}
-\end{figure}
-
-USB3.1 / Gigabit Ethernet converter to 5G \cite{rmeth}
-capable to connect RM520N module to its M2 connector header and acting as a 5G communication  bridge to PC, industrial control hosts, Raspberry Pi, ethernet switch or router using their USB3.1 or Ethernet connections.
-
-\subsubsection{Module form Jetson Nano}
-
-\begin{figure}[H]
-  \begin{center}
-	  \includegraphics[width=0.6\textwidth]{obrazky/rmjet.jpg}
-  \end{center}
-	\caption[Module for Jetson Nano]{Comunication module for Jetson Nano\cite{rmjet}}
-	\label{}
-\end{figure}
-
-Communication module for Jetson Nano \cite{rmjet}
-- interface with M2 connector, USB3.1 port, audio jack and decoder, SIM card slot, 40-pin GPIO extension header for direct connection to Jetson Nano, 4 antennas.
+%\section{Quectel RM520N}
+%
+%\begin{figure}[h!]
+%  \begin{center}
+%	  \includegraphics[width=0.6\textwidth]{obrazky/RM520N.png}
+%  \end{center}
+%	\caption[Quectel RM520N]{Quectel RM520N series front view\cite{rm520ndatasheet}}
+%	\label{}
+%\end{figure}
+%
+%RM520N is a 5G Sub-6GHz IoT module, made by Chinese company Quectel, optimized for IoT and eMBB applications with worldwide spectrum coverage, but capable of also 3G/4G multi-mode operation. The module is made in an M.2 form factor (30 x 52 x 2.3 mm) with 4 antenna connectors and is compatible with \ac{3GPP} Release 16 specification, supporting  both 5G NSA (data rates: 3.4 Gbps DL / 550 Mbps UL) and SA modes (data rates: 2.4 Gbps DL / 900 Mbps UL).
+%
+%The RM520N is an industrial-grade module for industrial and commercial applications. It should cover nearly all the mainstream carriers worldwide and support Qualcomm® IZat location technology Gen9C Lite (GPS, GLONASS, BDS and Galileo). The integrated GNSS receiver simplifies the product design.
+%
+%It communicates using USB and PCIe drivers provided by Quectel for Windows 7 or higher, Linux, and Android. Main anticipated usage are industrial routers, home gateways, laptops / tablet PCs as well as IoT applications \cite{rm520ndatasheet}.
+%
+%The module comes in two variants: RM520N-GL with global coverage and RM520N-EU with EU frequency regulatory spectrum.
+%
+%\subsection{Modules with RM520N}
+%
+%Development support for RM520N modules is provided by a Chinese company Waveshare \cite{waveshare1}\cite{waveshare2}
+%making several hardware kits for rapid development and implementation with RM520N and having a distribution network across EU (e.g. \url{https://rlx.sk/sk/vyhladavanie?controller=search&s=RM520N})
+%
+%\subsubsection{Dongle}
+%\begin{figure}[H]
+%  \begin{center}
+%	  \includegraphics[width=0.6\textwidth]{obrazky/rmdongle.jpg}
+%  \end{center}
+%	\caption[Waveshare dongle]{Waveshare dongle\cite{rmdongle}}
+%	\label{}
+%\end{figure}
+%
+%5G DONGLE module \cite{rmdongle}
+%providing simple expansion board with 4 SMA antenna connectors, nano SIM card holder, M2 connector for RM520N, heatsink and USB3.1 port for connecting to PC or Raspberry Pi.
+%
+%\subsubsection{Raspberry Pi HAT}
+%
+%\begin{figure}[H]
+%  \begin{center}
+%	  \includegraphics[width=0.6\textwidth]{obrazky/rmpi.jpg}
+%  \end{center}
+%	\caption[Waveshare dongle]{Waveshare dongle\cite{rmpi}}
+%	\label{}
+%\end{figure}
+%
+%5G HAT for Raspberry Pi \cite{rmpi}
+%, with a case for Raspberry Pi 3B/4B, onboard USB3.1 and USB-C ports, 2x SIM card slot, 4 antennas, 3A power supply circuit.
+%
+%\subsubsection{USB/Ethernet converter}
+%
+%\begin{figure}[H]
+%  \begin{center}
+%	  \includegraphics[width=0.6\textwidth]{obrazky/rmeth.jpg}
+%  \end{center}
+%	\caption[USB/Ethernet converter]{USB3.1 / Gigabit Ethernet converter to 5G\cite{rmeth}}
+%	\label{}
+%\end{figure}
+%
+%USB3.1 / Gigabit Ethernet converter to 5G \cite{rmeth}
+%capable to connect RM520N module to its M2 connector header and acting as a 5G communication  bridge to PC, industrial control hosts, Raspberry Pi, ethernet switch or router using their USB3.1 or Ethernet connections.
+%
+%\subsubsection{Module form Jetson Nano}
+%
+%\begin{figure}[H]
+%  \begin{center}
+%	  \includegraphics[width=0.6\textwidth]{obrazky/rmjet.jpg}
+%  \end{center}
+%	\caption[Module for Jetson Nano]{Comunication module for Jetson Nano\cite{rmjet}}
+%	\label{}
+%\end{figure}
+%
+%Communication module for Jetson Nano \cite{rmjet}
+%- interface with M2 connector, USB3.1 port, audio jack and decoder, SIM card slot, 40-pin GPIO extension header for direct connection to Jetson Nano, 4 antennas.
+%
\ No newline at end of file